温度对PSⅡCP4 7/D1/D2/Cytb559复合物荧光光谱特性的影响

采用激励光源为514.5 nm的分幅扫描单光子计数荧光光谱装置对经20℃、42℃和48℃不同温度处理后的反应中心复合物CP47/D₁/D₂/Cyt b559的荧光光谱特性进行了研究.经解析,获得不同温度处理后,CP47/D₁/D₂/Cyt b559复合物最大峰值未发生变化,均在682 nm,说明Chla670的能量都由Chla682接收,但损耗愈来愈小,在48℃时,损耗程度最小,而其荧光百分比未发生多大变化.振动副带～700 nm和～740 nm的中心波长都发生蓝移,在不同温度下分别为:20℃ 703 nm,749 nm;42℃ 697 nm,744 nm;48℃ 694 nm,740 nm.因此可以推测温度的升高,影响了CP47/D₁/D₂/Cyt b559色素蛋白的二级结构以及色素分子的空间位置,使最大峰值处的荧光强度逐渐降低,振动副带逐渐蓝移.42℃的温度已造成影响,48℃影响较大.     

电致发光色纯性增强的硅基有机微腔

报道了硅基有机微腔的电致发光（EL）.该微腔由上半透明金属膜、中心有源多层膜和多孔硅分布Bragg反射镜（PS DBR）组成.半透明金属膜由Ag（２０nm）构成，充当发光器件的负电极和微腔的上反射镜.有源多层膜由Al (1 nm) / LiF(05 nm) /Alq3/Alq3:DCJTB/NPB/CuPc/ITO/SiO2组成，其中的Al/LiF为电子注入层，ITO为正电极，SiO2为使正、负电极电隔离的介质层.该PS DBR是采用设备简单、成本低廉且非常省时的电化学腐蚀法用单晶Si来制备的；该PS 关键词： 电化学腐蚀 电致发光 窄峰发射 硅基有机微腔     

Au(111)上烷烃硫醇SAMs表面应力的理论研究

应用已建立的关于金属表面吸附层中表面应力的统计热力学理论 ,计算了Au(111)上烷烃硫醇SAMs的表面应力及其与烷烃硫醇链长、吸附覆盖度的定量关系 .计算结果与实验相符 ,较好地解释了Berger等人的实验结果 ,特别是解决了在表面应力符号性质上理论与实验的矛盾 .在表面吸附层应力的多种物理起源中 ,通过底物的分子间作用力有着决定性的贡献 ,揭示了分子的吸附能间接地起着重要作用 .这与阴离子化学吸附体系Cl-/Au(111)的有关研究结果相同 .     

Synthesis,characterization, and curing kinetics of novel ladder‐like polysilsesquioxanes containing side‐chain maleimide groups

Two ladder‐like polysilsesquioxanes (LPS) containing side‐chain maleimide groups have been synthesized successfully by reacting N‐(4‐hydroxyphenyl)maleimide (HPM) with LPS containing 100 mol % of chloropropyl groups (Ladder A ) and 50 mol % of each methyl and chloropropyl group (Ladder B ). HPM was synthesized by reacting maleic anhydride with 4‐aminophenol, and the resulting amic acid was imidized using p‐toluenesulfonic acid as a catalyst (Scheme 1 ). The LPSs were characterized by Fourier transform infrared (FTIR), ¹H nuclear magnetic resonance (NMR), proton‐decoupled ¹³C NMR, ²⁹Si NMR, wide‐angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). Characterization indicated that these polymers had ordered ladder‐like structures with possible defects. These polymers were soluble in common solvents at ambient temperature, which suggested that they were not crosslinked. Both the polymers and the HPM were cured, and their kinetics were followed by dynamic DSC. The Ozawa and Kissinger methods were used to calculate activation energies for curing. Curing increased the temperature at which both 5% weight loss and maximum rate of weight loss were observed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4036–4046, 2004     

Mutual influence of the morphology and capillary rheological properties in nylon/glass‐fiber/liquid‐crystalline‐polymer blends

Nylon‐6/glass‐fiber (GF)/liquid‐crystalline‐polymer (LCP) ternary blends with different viscosity ratios were prepared with three kinds of nylon‐6 with different viscosities as matrices. The rheological behaviors of these blends were characterized with capillary rheometry. The morphology was observed with scanning electron microscopy and polarizing optical microscopy. This study showed that although LCP did not fibrillate in binary nylon‐6/LCP blends, LCP fibrillated to a large aspect ratio in some ternary blends after GF was added. The addition of 5 wt % LCP significantly reduced the melt viscosity of nylon‐6/GF blends to such an extent that some nylon‐6/GF/LCP blends had quite low viscosities, not only lower than those of neat resins and nylon‐6/GF blends but also lower than those of corresponding nylon‐6/LCP blends. The mutual influence of the morphology and rheological properties was examined. The great reduction of the melt viscosity was considered the result of LCP fibrillation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1619–1627, 2004     

Effect of α‐cyclodextrin on the crystallization of poly (3‐hydroxybutyrate)

The effect of α‐cyclodextrin (α‐CD) on the crystallization behavior of poly(3‐hydroxybutyrate) (PHB) was investigated with polarized optical microscopy, differential scanning calorimetry, and wide‐angle X‐ray diffraction. We found that the addition of α‐CD can greatly accelerate the crystallization of PHB and that α‐CD has a potential not only to enhance the nucleation but also to accelerate the crystallization of PHB. Compared to a conventional nucleation agent, such as talc, α‐CD is a natural product and has many advantages because it is environmentally friendly and safe to humans. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3461–3469, 2004     

0.8W/80K直线驱动斯特林制冷机的研制

介绍了一种 0 .8W/ 80 K分置式斯特林制冷机。该制冷机采用当前国外先进的直线电机驱动 ,双活塞对称布置结构。该制冷机已通过军品所要求的环境试验 ,输入功率小于 4 0 W(DC)情况下 ,其 +6 0℃高温环境下制冷量≥ 0 .5 W/ 80 K ,带载 0 .5 W工况下 MTTF已突破 2 0 0 0小时。文中主要论述了其工作原理、结构特点、试验情况。     

薄膜外延生长的计算机模拟

以Cu膜为例，用Monte-Carlo算法模拟了薄膜生长的随机过程，并提出了更加完善的模型.在合理选择原子间相互作用计算方法的基础上，考虑了原子的吸附、在生长表面的迁移及迁移所引起的近邻原子连带效应、从生长表面的脱附等过程.模拟计算了薄膜的早期成核情况以及表面粗糙度和相对密度.结果表明，随着衬底温度的升高或入射率的降低，沉积在衬底上的原子逐步由离散型分布向聚集状态过渡形成一些岛核，并且逐步由二维岛核向三维岛核过渡.在一定的原子入射率下，存在三个优化温度，成核率最高时的最大成核温度Tn、薄膜的表面粗糙度最低 关键词： Monte-Carlo算法 计算机模拟 薄膜生长     

多目标优化发射层析算法在等离子体场光谱诊断中的应用

提出一种基于多目标优化原理的发射光谱层析(EST)图像重建新算法MCIRT.通过计算机数值 模拟，考察了该算法对非对称发射系数场分布的重建效果.结果表明，与传统层析算法相比 ，MCIRT算法具有收敛快，重建精度高的优势，适合于非完全数据情况下的等离子体发射系 数场重建，并且实时性更好.作为一个应用实例, 运用谱线相对强度法重建了自由电弧等离 子体的三维温度及粒子数密度分布. 关键词： 等离子体诊断 图像重建     

p型导电掺In的SnO2薄膜的制备及表征

采用溶胶-凝胶提拉法成功地制备了p型导电掺In的SnO2薄膜.x射线衍射测试结果表明，掺In的SnO2薄膜保持SnO2的金红石结构.吸收谱测试结果表明，掺In的SnO2禁带宽度为3.8eV.霍尔测量结果表明，空穴浓度与热处理温度有很大的关系，525℃为最佳热处 理的温度.铟锡原子比在0.05—0.20范围内，空穴的浓度与In的含量有直接的关系，并随In含量的增加而增加. 关键词： SnO2 溶胶-凝胶法 p型导电